Factory: 1 building, 1-st st, Noragavit
Corrugated sheet KP 8 is manufactured from PPGI sheets according to:
GOST EN 10326-DX51D
Stuff: Korea (20 years' factory warranty for paint quality)
1.Steel Sheet
2.Z 225-275
3.Passivation layer
4.Primer 10 micron
5.Polyester 25 micron
6.Protective Lacquer
7.Sheet’s thickness 0.40-0.50 mm
8. Sheet’s Width 1250 mm
Name | նկար | GOST | Sheet Thickness mm | Sheet Width mm | Sheet Mounting Width mm | 1 m2 Weight | M/U |
---|---|---|---|---|---|---|---|
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.45 | 1200 | 1140 | 3.843 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.47 | 1200 | 1140 | 4.089 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.45 (matt) | 1200 | 1140 | 3.680 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.47 (matt) | 1200 | 1140 | 3.843 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.50 (matt) | 1200 | 1140 | 4.089 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.50 (Camouflage) | 1200 | 1140 | 4.089 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.50 (Multi Gloss) | 1200 | 1140 | 4.089 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10346-DX51D,EN10143 | 0.40 (two tone) | 1200 | 1140 | 3.271 | m2 | |
Pre-Painted corrugated sheet Kp 8 | EN 10326-DX51D | 0.50 (two tone) | 1200 | 1140 | 4.089 | m2 | |
Pre-Painted corrugated sheet Kp 8 | ГОСТ- EN 10326-DX51D | 0.50 | 1200 | 1140 | 4.089 | m2 |
Galvanized corrugated sheet KP 8 is one of the most universal profiles, widely used in modern construction. Corrugated sheet KP 8 is the most economical corrugated sheet, it’s used as wall facing material, as well as for the construction of fences and installation of suspended ceilings. Despite the fact that its load-carrying capacity is relatively low, often the galvanized corrugated board KP 8 is also used for the installation of roof coverings of pitched roofs with an angle of inclination greater than 30-40 °.
Profiled sheeting KP 8 for fencing and roofing is manufactured by the cold rolled method in accordance with GOST 24045-94 and TU 1122-079-02494680-01 of steel sheet with a thickness of 0.25 to 0.7 mm. As a raw material, roll cold rolled steel of grades 01 and 220-350 in accordance with GOST P 52246-2004 with zinc protective coating is used according to GOST EN 10326-DX51D
The corrugated sheet KP 8 is not used in load-bearing structures, since the ability of the profiled sheet to with stand the load depends on the height of the wave, and 8 mm is the smallest value. Therefore, such a corrugated board is mainly used for the following tasks: finishing the facade of buildings; manufacturing of sandwich panels; manufacturing auxiliary buildings on sites by private developers, warehouse, barn, farm block and others.